FAQ

FAQ’S –MdsMat™

How easy is the system installation?
When installing under tiles, the heating mats are simply laid directly between the sub-floor and tile. The same materials used for laying tiles are used for bonding the electric radiant heating mats to your sub-floor. When installing under timber or parquet floors, the installer lays the heating mats on the sub-floor and lays the timber elements directly on the mats in the same manner as a standard timber installation. A certified electrician can complete the connection between the heating mats and the electrical circuit. No time-consuming calculations, labor or additional materials are required.

How efficient are the heating mats under wooden or carpeted floors?
Because MDSMAT™ mats are constructed of ultra-thin crystalline ribbon (2/1000th on an inch (40-65 microns), so heat is not absorbed by the metal. It is therefore immediately transferred to the floor area and the ribbon temperature remains relatively low at approximately 82-86ºF / 27-30ºC. This attribute is crucial under wood and carpet installations which can be easily damaged by higher temperatures.

What are the safety measures against electrical shock hazard?
We place maximum emphasis on safety and performance of the electrical resistance of our coating. With our integral grounding our product is rendered a class 2, double insulation product. As such, it has been tested and found to comply with UL 1693 and CNL-CSA C22.2 No 217 and L-13. The installation complies with NEC- National Electrical Code -part J, meaning the product has sufficient electrical resistance according to the strictest standards. We also test each unit in the production line for electric withstand of 2500 volts, once again, according to the relevant UL & CUL standards for unit inspections in the production line. The electric withstand testing is repeated on each unit after installation using a Megger tester, and the measured resistance value is recorded on the warranty card.

All the applicable standards, codes and practices require the mandatory incorporation of a RCD/GFCI in the electrical circuitry of an electrical under-floor heating system, while leaving the option of including a metallic shield around the heating element as an additional safety design consideration for the element manufacturer.

What are the recommended RCD/GFCI characteristics to be used with the system?
Electric circuit that supplies electricity to the underfloor heating system must be equipped with a 30 mA ground fault current interrupter (GFCI). For wet areas ensure that the electric circuit that supplies electricity to the heating system is equipped with a 5 mA ground fault current interrupter (RCD/GFCI). Wet areas include: saunas, bathrooms, utility rooms, and kitchen areas within 20 inches (50 cm) of sinks or any metallic kitchen appliance. Our thermostats include a built-in GFCI.

What’s special about Crystalline ribbons?
The homogeneous, singular structure of crystalline metallic alloys provides unique mechanical, anti-corrosion, wear resistant, and magnetic properties. It renders crystalline metallic alloys superior in many ways to the more common metals.

Why is MDSMAT™ Crystalline ribbon an excellent heating element for moderate temperature heaters?
Due to the crystalline structure, crystalline ribbons have higher electrical resistance than other solids of the same composition. Together with the physical form of the ribbon, which provides a low mass to surface area ratio, it makes the ribbon a very attractive candidate as a heating element. Why?
The explanation is very simple: energy transfer from any heating element is proportional to its surface area and the temperature difference between the heater and its environment. The larger the surface area, the lower the temperature difference needed to transfer energy from the heater to its environment.

Since the surface area of the ribbon is relatively large (compare it with the surface area of a conventional wire used in many heaters) it is able to efficiently transfer heat to its environment at lower temperatures. In a domestic heating environment, lower temperature means a healthier environment and greater safety and durability.

What’s unique about MDSMAT™ Crystalline ribbons?
MdsHeat is the only company using crystalline ribbons for heating applications (Covered by Patents in the USA and EU). The MDSMAT™ ribbons are more reliable, with higher electrical and corrosion resistance. Their main characteristics are:

 Thickness   40-60 mm (micro foot)
 Width   3-100 mm 6.56 – 328 mft (milli-foot)
 Corrosion resistance  High (nickel and chrome based)
 Ductility and flexibility  High
 Heat transfer area  High
 Warm-up time to steady state Low

Why are MDSMAT™ mats of special interest for underfloor heating?
Many features of MDSMAT™ heating mats make them attractive for surface heating:

  • Efficient heat transfer because of the large surface area and the ultra-thinness of the ribbons that prevents heat absorption by the metal. This enables the mats to be used under wood and carpets.
  • They eliminate risk, never heating too much to change the characteristic of the metal.
  • Faster and more efficient heating because the mats can be placed directly under the surface in most cases (while competitive systems need to be embedded in cement due to their high temperature).
  • Low heating inertia because of the low mass of the ribbon.  Especially in a more rapidly fluctuating (on/off) mode, you can expect energy savings due to both low heating inertia and efficient heat transfer.
  • Possibility of using cheaper or less insulating material because of the lower heating temperature used.
  • Very convenient physical shape, allowing fast and easy installation.
  • Higher reliability because of the low heating temperature, high mechanical strength and corrosion resistance properties.

Installation Manuals

MdsMat™ Installation Manual USA 8W & 12W

MdsMat™ Installation Manual Europe

MdsMat™ Installation Manual 120W French

Roll’n’ Warm™ Installation Manual World Wide

 

Call Now Button